Flagship Flags
(800)253-5247
San Diego, California
If you don't see a black vertical frame, click here ,then select Large Pole Accessories from the black frame.
Back to Flagpole Accessories page
External Halyard Trucks
|
|
|
Cast aluminum construction with a cast nylon sheave. Designed to slip over the top of the flagpole and be secured by a stainless steel screw. Top of the assembly is tapped 1/2"-13NC to accept a finial. Maximum recommended halyard diameter is 1/4". |
| Pole Top Diameter | MDL | Matte Finish |
| 1 3/8" | ST1-138 | $25.00 |
| 1 1/2" | ST1-112 | $25.00 |
| 1 3/4" | ST1-134 | $25.00 |
 |
STATIONARY TRUCK - SINGLE SHEAVE
Cast aluminum construction with a cast nylon sheave on a 1/4" aluminum axle. Designed to slip over the top of the flagpole and be secured by three 1/4"-20NC stainless steel set screws. Top of the assembly is tapped 1/2"-13NC to accept a finial. Maximum recommended halyard diameter is 5/16". |
| Pole Top Diameter | MDL | Matte Finish | Pole Top Diameter | MDL | Matte Finish |
| 1 7/8" - 2" | TRK-9100 | $27.00 | 3 1/2" | TRK-9320 | $45.50 |
| 2 3/8" | TRK-9200 | $29.00 | 4" | TRK-9210 | $89.00 |
| 2 7/8" - 3" | TRK-9300 | $30.50 | 4 1/2" | TRK-9220 | $89.00 |
 |
REVOLVING TRUCK - SINGLE OR DOUBLE SHEAVE Cast aluminum construction with cast nylon sheave(s) on 1/4" aluminum axle(s). The truck body rotates on 26 stainless steel ball bearings on cast races. The SINGLE SHEAVE TRUCK can be used on flagpoles with up to a 3 1/2" O.D. top while the DOUBLE SHEAVE TRUCK can be used on up to 4" O.D. tops. The top of the spindle is tapped 1/2"-13NC as standard to accept a finial. Maximum recommended halyard size is 5/16". |
| Spindle Thread Size | Single Sheave | Matte Finish | Double Sheave | Matte Finish | |
| 1 1/4" NPT Nylon pulley | $60.00 | TRK-9600 | $70.00 | TRK-9700 |
| 1 1/4" NPT Alum pulley | $66.00 | TRK-9610 | $78.50 | TRK-9710 |
 |
REVOLVING TRUCK - CAP STYLE - SINGLE OR DOUBLE SHEAVE
Same specifications as the single and double revolving trucks shown above except that the threaded spindle is replaced with a cast slip over cap and secured to the shaft by three 1/4"-20NC stainless steel set screws. |
| Pole Top Diameter | Matte finish | Single Sheav | Matte finish | Double Sheave |
| 1 7/8" - 2" | TRK-9350 | $66.00 | TRK-9360 | $71.00 |
| 2 3/8" | TRK-9365 | $72.00 | N.A | N.A |
| 2 7/8" - 3" | TRK-9370 | $74.00 | TRK-9380 | $77.00 |
 |
CAP STYLE TRUCK ADAPTERS
For use in mounting a revolving truck assembly to a pole without a threaded end plug. Unit is tapped 1 1/4" NPT and is secured to the shaft by three 1/4"-NC stainless set screws or by drilling and tapping the shaft to the accept bolts. |
| Pole Top Diameter | MDL | Matte Finish |
| 2" | TRK-2000 | 45.00 |
| 2 3/8" | TRK-2020 | 45.00 |
| 3" | TRK-2030 | 50.00 |
| 3 1/2" | TRK-2045 | 51.00 |
| 4" | TRK-2050 | 63.00 |
|
LIGHT POLE OR TELEPHONE POLE PULLEY
Ideal for use in adding flags or decorative banners to small area lighting poles in applications such as shopping center or automobile dealerships. Cast aluminum construction with cast nylon sheave on a 1/4" aluminum axle. Attaches with four 1/4"-20NC stainless steel flathead screws to a light standard at any desired height. |
| Matte Finish | TRK-9150 | $18.00 |
Back to Flagpole Accessories page
courtesy FCI